AT Commands For HSIC_LAN

  

No	Command	Description
L2501	AT+CENABLELAN	Enable LAN function
L2502	AT+CLANMODE	Set LAN mode
L2503	AT+CLANCTRL	Set LAN configure
L2504	AT+CHSICSLEEP	Allow Hsic Device Go to AutoSleep

 

 

 

 

L2501    AT+CENABLELAN     Enable LAN Function

 

W) AT+CENABLELAN=<onoff>

OK or ERROR

  

<onoff>

0     Close the LAN9730 1     Open the LAN9730

 

Example

AT+CENABLELAN=1 OK

 

NOTE

LAN9730 is not opened in default, if want to open the LAN9730, you can run AT+CENABLELAN=1.

After run this command, the module will restart automatically, then the LAN9730 will be opened.

If want to close the LAN9730, you can run AT+CENABLELAN=0. 

After run this command, the module will restart automatically, then the LAN9730 will be closed.

WIFI firmware doesn’t care this AT command.

 

 

 

 

L2502   AT+CLANMODE     Set LAN Mode

 

T) AT+CLANMODE=?	+CLANMODE: (list of supported <mode>s) OK
R) AT+CLANMODE?	+CLANMODE: <mode> OK
W) AT+CLANMODE=<mode>	OK or OK

  

<mode>

0     lan mode 1     wan mode 2     static ip mode

 

Example

AT+CLANMODE? +CLANMODE: (0,1) OK AT+CLANMODE=1 OK

                                               

                                                           

NOTE

Module works in lan mode in default. If want to use another mode, need to run at+clanmode=<mode>,

after run this command, module will restart automatically, then the module will work in target mode.

 

 

 

 

 L2503   AT+CLANCTRL     Set LAN Configure

 

T) AT+CLANCTRL=?	+CLANCTRL: (list of supported <option>s)   OK
W) AT+CLANCTRL=<option>,[[type/ip],[netmask]]	OK or ERROR

  

<option>	0        uninstall driver 1        install driver 2        set mac address 3        set ip address 4        bring up eth0 5        bring down eth0
<type>	1        bcm898xx 2        at803x
<ip>	LAN ip address (Range: 192.168.*.*).
<netmask >	Range     255.255.*.* if the parameter is not set, will use the default value:255.255.255.0

  

Example

AT+CLANCTRL=3,”192.168.1.1”                                        Set ip. The netmask is use default value 255.255.255.0                                                                                     OK AT+CLCANCTRL=3,”192.168.1.1”,”255.255.2 55.0” Set ip and netmask. The netmask is 255.255.255.0 OK

 

 

NOTE

Uninstall driver (option=0). Not support for HSIC LAN, Only Support SGMII LAN. Please don’t run this command on HSIC LAN module

Install driver (option=1). Not support for HSIC LAN, Only Support SGMII LAN.

Set mac address (option=2). Support for HSIC LAN, But the module will auto set the Mac address. So there is no need to run the command.

Set ip address (option=3). When module work in static ip mode. Use this command set ip and netmask.

Bring up eth0 bring up eth0 (option=4). equal to “ifconfig eth0 up”

Bring down eth0 (option=5). equal to “ifconfig eth0 down”

 

 

 

 

L2504   AT+CHSICSLEEP     Allow HSIC Device Go To AutoSleep

 

T) AT+CHSICSLEEP=?	+CHSICSLEEP: (list of supported <state>s)  OK
R) AT+CHSICSLEEP?	+CHSICSLEEP: <state>  OK
W) AT+CHSICSLEEP=<state>	OK or ERROR

  

<state>

0       Don’t allow the hsic device go to autosleep 1       Allow the hsic device go to autosleep

 

Example

AT+CHSICSLEEP =1 OK  AT+CHSICSLEEP? +CHSICSLEEP: 1 OK

 

NOTE

If the module needs to go to sleep, user needs to execute following steps:

1. AT+CHSICSLEEP=1

2. AT+CLANCTRL=5