TX Test with Rail Application
There are 3 transmission modes in rail test and each modes should be used for a corresponding measurement.
| Test Parameter | CW Mode | PN9 Mode | Packet Mode | |
| TX Power | X | O | O | |
| Power Spectral Density Mask | O | X | O | |
| Phase Noise | X | O | O | |
| Spurious Emission | X | O | O | |
| Transient Power | O | O | X |
1. TX in CW Mode
TE(Test Equipment), DUT(Device Under Test)
| NO | Device | Command | 설명 | |
| 1 | DUT | setTxTone 0 | TX to Idle | |
| 2 | DUT | rx 0 | RX to Idle | |
| setDebugMode 0 | ||||
| setConfigIndex 0 | Select PHY if multi-PHY configuration | |||
| 3 | DUT | setchannel 0 | Set Channel(Frequency) | |
| setDebugMode 1 | 임의의 주파수로 설정하고자 할 때 | |||
| freqOverride 915000000 | 임의의 주파수로 설정하고자 할 때 | |||
| 4 | DUT | setTxStream 1 0 | Enable CW Mode | |
| setTxTone 1 | setTxStream 대신 사용가능 |
2. TX in PN9 Mode
TE(Test Equipment), DUT(Device Under Test)
| NO | Device | Command | 설명 | |
| 1 | DUT | setTxStream 0 1 0 | TX to Idle | |
| 2 | DUT | rx 0 | RX to Idle | |
| 3 | DUT | setPower 130 | Set RF Output Power | |
| setDebugMode 0 | ||||
| setConfigIndex 0 | Select PHY if multi-PHY configuration | |||
| 3 | DUT | setchannel 0 | Set Channel(Frequency) | |
| setDebugMode 1 | 임의의 주파수로 설정하고자 할 때 | |||
| freqOverride 915000000 | 임의의 주파수로 설정하고자 할 때 | |||
| 4 | DUT | setTxStream 1 1 0 | Enable PN9 Mode |
3. TX in Packet Mode
TE(Test Equipment), DUT(Device Under Test)
| NO | Device | Command | 설명 | |
| 1 | DUT | tx 0 | tx 0 is toggle command between Idle and continuous TX | |
| 2 | DUT | rx 0 | RX to Idle | |
| 3 | DUT | setPower 130 | Set RF Output Power | |
| setDebugMode 0 | ||||
| setConfigIndex 0 | Select PHY if multi-PHY configuration | |||
| 4 | DUT | setchannel 0 | Set Channel(Frequency) | |
| setDebugMode 1 | 임의의 주파수로 설정하고자 할 때 | |||
| freqOverride 915000000 | 임의의 주파수로 설정하고자 할 때 | |||
| printTxPacket | Can check the payload to be sent | |||
| setTxPayload 2 0x01 0x02 0x03 0x04 | Can change the payload, pointed by byte-offset | |||
| setTxLength 16 | Can change packet length to be sent in byte, default is 16. | |||
| setTxDelay 250 | TX delay between packet in ms , default is 250ms | |||
| 4 | DUT | tx 500 | n times tx, if tx 0 then infinitely/continuously transmit |
WiFi IoT Module
Bluetooth Module
5G/LTE/CAT-M1/NB-IoT
