페이지 선택
Generic selectors
Exact matches only
Search in title
Search in content
Search in pages
AT Commands for  Status Control 

 

Command Description
AT+CFUN Set phone functionality
AT+CPIN Enter PIN
AT+CICCID Read ICCID from SIM card
AT+CSIM Generic SIM access
AT+CRSM Restricted SIM access
AT+SPIC Times remain to input SIM PIN/PUK
AT+CSPN Get service provider name from SIM
AT+CSQ Query signal quality
AT+AUTOCSQ Set CSQ report
AT+CSQDELTA Set RSSI delta change threshold
AT+CATR Configure URC destination interface
AT+CPOF Power down the module
AT+CRESET Reset the module
AT+CACM Accumulated call meter
AT+CAMM Accumulated call meter maximum
AT+CPUC Price per unit and currency table
AT+CCLK Real time clock management
AT+CMEE Report mobile equipment error
AT+CPAS Phone activity status
AT+SIMEI Set IMEI for the module
AT+SMEID Request Mobile Equipment Identifier
AT+CSVM Voice Mail Subscriber number

 

 

 

 

AT+CFUN      Set phone functionality

This command is used to select the level of functionality <fun> in the ME.

Level “full functionality” is where the highest level of power is drawn. “Minimum functionality” is where minimum power is drawn.

Level of functionality between these may also be specified by manufacturers.

When supported by manufacturers, ME resetting with <rst> parameter may be utilized.

 

NOTE:

AT+CFUN=6 must be used after setting AT+CFUN=7.

If module in offline mode, must execute AT+CFUN=6 or restart module to online mode.

 

T) AT+CFUN=?

Response

+CFUN: (list of supported <fun>s),(list of supported <rst>s)
OK

or

ERROR

or

+CME ERROR: <err>

R) AT+CFUN?

Response

+CFUN: <fun>
OK

or

ERROR

or

+CME ERROR: <err>

W) AT+CFUN=<fun>[,<rst>]

Response

OK

or

ERROR

or

+CME ERROR: <err>

 

 

♦Parameter
Description
<fun>

0- minimum functionality

1- full functionality, online mode

4- disable phone both transmit and receive RF circuits

5- Factory Test Mode

6-Reset

7- Offline Mode

<rst>

0-  do not reset the ME before setting it to <fun> power level

1- reset the ME before setting it to <fun> power level. This value only takes effect when <fun> equals 1.

 

 

♦Examples

AT+CFUN?

+CFUN: 1

 OK AT+CFUN=0 OK

 

 

 

 

AT+CPIN               Enter PIN

This command is used to send the ME a password which is necessary before it can be operated (SIM PIN, SIM PUK, PH- SIM PIN, etc.).

If the PIN is to be entered twice, the TA shall automatically repeat the PIN.

If no PIN request is pending, no action is taken towards MT and an error message, +CME ERROR, is returned to TE.

If the PIN required is SIM PUK or SIM PUK2, the second pin is required. This second pin, <newpin>, is used to replace the old pin in the SIM.

 

 

T) AT+CPIN=?

Response

OK

R )AT+CPIN?

Response

+CPIN: <code>

OK

or

ERROR

or

+CME ERROR: <err>

W) AT+CPIN=<pin>[,<newpin>]

Response

OK

or

ERROR

or

+CME ERROR: <err>

 

 

♦Parameter
Description
<pin> String type values.
<newpin> String type values.
     <code>

Values reserved by the present document:

READY – ME is not pending for any password

SIM PIN – ME is waiting SIM PIN to be given

SIM PUK – ME is waiting SIM PUK to be given

PH-SIM PIN – ME is waiting phone- to- SIM card password to be given

SIM PIN2 – ME is waiting SIM PIN2 to be given

SIM PUK2 – ME is waiting SIM PUK2 to be given

PH-NET PIN–  ME is waiting network personalization password to be given

 

 

♦Examples

AT+CPIN?

+CPIN: SIM PUK2

 OK

 

 

 

 

AT+CICCID          Read ICCID from SIM card

This command is used to Read the ICCID from SIM card

 

T) AT+CICCID=?

Response

OK

E) AT+CICCID

Response

+ICCID: <ICCID>

OK

or

ERROR

or

+CME ERROR: <err>

 

 

♦Parameter
Description
<ICCID> Integrate circuit card identity, a standard ICCID is a 20-digit serial number of the SIM card,it presents the publish state, network code, publish area, publish date, publish manufacture and press serialnumber of the SIM card.

 

 

♦Examples

AT+CICCID

+ICCID: 898600700907A6019125

 OK

 

 

 

 

AT+CSIM     Generic SIM access 

This command is used to control the SIM card directly.

Compared to restricted SIM access command AT+CRSM, AT+CSIM allows the ME to take more control over the SIM interface.

For SIM–ME interface please refer 3GPP TS 11.11.

 

NOTE

The SIM Application Toolkit functionality is not supported by AT+CSIM.

Therefore the following SIM commands can not be used: TERMINAL PROFILE, ENVELOPE, FETCH and TEMINAL RESPONSE.

 

T) AT+CSIM=?

Response

OK

W) AT+CSIM=<length>,<comm and>

Response

+CSIM: <length>,<response>

OK

or

ERROR

or

+CME ERROR: <err>

 

 

♦Parameter
Description
<length> Interger type; length of characters that are sent to TE in<command>or<response>
<command> Command passed from MT to SIM card.
<response> Response to the command passed from SIM card to MT.

 

 

♦Examples

AT+CSIM=?

OK

 

 

 

 

AT+CRSM         Restricted SIM access

By using AT+CRSM instead of Generic SIM Access AT+CSIM, TE application has easier but more limited access to the SIM database.

Write command transmits to the MT the SIM <command> and its required parameters.

MT handles internally all SIM-MT interface locking and file selection routines.

As response to the command, MT sends the actual SIM information parameters and response data.

MT error result code +CME ERROR may be returned when the command cannot be passed to the SIM,

but failure in the execution of the command in the SIM is reported in <sw1> and <sw2> parameters.

 

T) AT+CRSM=?

Response

OK

W) AT+CRSM=<command>[,<fil eID>[,<p1>,<p2>, <p3>[,<data>]]]

Response

+CRSM: <sw1>,<sw2>[,<response>]
OK

or

ERROR

or

+CME ERROR: <err>

 

♦Parameter
Description
<command>

Command passed on by the MT to the SIM:

176   –    READ BINARY

178   –    READ RECORD

192   –    GET RESPONSE

214   –    UPDATE BINARY

220   –    UPDATE RECORD

242   –    STATUS

203   –    RETRIEVE DATA

219   –    SET DATA

<fileID>

Identifier for an elementary data file on SIM, if used by<command>.

The following list the fileID hex value, user needs to convet them to decimal.

EFs under MF

 

0x2FE2            ICCID

0x2F05            Extended Language Preferences

0x2F00            EF DIR

0x2F06            Access Rule Reference EFs under USIM ADF

0x6F05              Language Indication

0x6F07              IMSI

0x6F08              Ciphering and Integrity keys

0x6F09              C and I keys for pkt switched domain

0x6F60              User controlled PLMN selector w/Acc Tech

0x6F30              User controlled PLMN selector

0x6F31              HPLMN search period

0x6F37              ACM maximum value

0x6F38              USIM Service table

0x6F39              Accumulated Call meter

0x6F3E              Group Identifier Level

0x6F3F              Group Identifier Level 2

0x6F46              Service Provider Name

0x6F41              Price Per Unit and Currency table

0x6F45             Cell Bcast Msg identifier selection

0x6F78              Access control class

0x6F7B              Forbidden PLMNs

0x6F7E              Location information

0x6FAD              Administrative data

0x6F48              Cell Bcast msg id for data download

0x6FB7              Emergency call codes

0x6F50              Cell bcast msg id range selection

0x6F73              Packet switched location information

0x6F3B              Fixed dialling numbers

0x6F3C              Short messages

0x6F40              MSISDN

0x6F42              SMS parameters

0x6F43              SMS Status

0x6F49              Service dialling numbers

0x6F4B              Extension 2

0x6F4C              Extension 3

0x6F47              SMS reports

0x6F80              Incoming call information

0x6F81              Outgoing call information

0x6F82              Incoming call timer

0x6F83              Outgoing call timer

0x6F4E              Extension 5

0x6F4F              Capability Config Parameters 2

0x6FB5              Enh Multi Level Precedence and Pri

0x6FB6              Automatic answer for eMLPP service

0x6FC2              Group identity

0x6FC3              Key for hidden phonebook entries

0x6F4D              Barred dialling numbers

0x6F55              Extension 4

0x6F58              Comparison Method information

0x6F56              Enabled services table

0x6F57              Access Point Name Control List

0x6F2C              De-personalization Control Keys

0x6F32              Co-operative network list

0x6F5B              Hyperframe number

0x6F5C            Maximum value of Hyperframe number

0x6F61              OPLMN selector with access tech

0x6F5D              OPLMN selector

0x6F62              HPLMN selector with access technology

0x6F06              Access Rule reference

0x6F65              RPLMN last used access tech

0x6FC4              Network Parameters

0x6F11              CPHS: Voice Mail Waiting Indicator

0x6F12,              CPHS: Service String Table

0x6F13              CPHS: Call Forwarding Flag

0x6F3D              Capability Configuration Parameters

0x6F4F              Extended CCP

0x6F40              MSISDN

0x6F42              SMS parameters

0x6F43              SMS Status

0x6F44              Last number dialled

0x6F49              Service Dialling numbers

0x6F4A              Extension 1

0x6F4B              Extension 2

0x6F4C              Extension 3

0x6F4D              Barred Dialing Numbers

0x6F4E              Extension 4

0x6F47              SMS reports

0x6F58              Comparison Method Information

0x6F54              Setup Menu elements

0x6F06              Access Rule reference

0x4F20              Image

0x4F30              Phone book reference file

0x4F22              Phone book synchronization center

0x4F23              Change counter

0x4F24              Previous Unique Identifier

<p1><p2><p3> Integer type; parameters to be passed on by the Module to the SIM.
<data>

Information which shall be written to the SIM

(hexa decimal character format, refer AT+CSCS).

<sw1><sw2>

Status information from the SIM about the execution of the actual command.

It is returned in both cases, on successful or failed execution of the command.

<response>

Response data in case of a successful completion of the previously issued command.

“STATUS” and “GET RESPONSE” commands return data,

which gives information about the currently selected elementary data field.

This information includes the type of file and its size.

After “READ BINARY” or “READ RECORD” commands the requested data will be returned.

<response> is empty after “UPDATE BINARY” or “UPDATERECORD” commands.

 

 

♦Examples AT+CRSM=? OK

 

 

 

 

AT+SPIC          Times remain to input SIM PIN/PUK

This command is used to inquire times remain to input SIM PIN/PUK.

 

T) AT+SPIC=?

Response

OK

E) AT+SPIC

Response

+SPIC: <pin1>,<puk1>,<pin2>,<puk2>
OK

 

 

♦Parameter
Description
<pin1> Times remain to input PIN1 code.
<puk1> Times remain to input PUK1 code.
<pin2> Times remain to input PIN2 code.
<puk2> Times remain to input PUK2 code.

 

 

♦Example

AT+SPIC=?

OK

AT+SPIC

+SPIC: 3,10,0,10

 OK

 

 

 

 

AT+CSPN       get service provider name from SIM card.

This command is used to get service provider name from SIM card.

 

T) AT+CSPN=?

Response

OK

or

ERROR

R) AT+CSPN?

Response

+CSPN: <spn>,<display mode>

OK

or

ERROR

or

+CME ERROR: <err>

 

 

♦Parameter
Description
<spn> String type; service provider name on SIM
<display mode> 0       –    doesn’t display PLMN. Already registered on PLMN.1       –    display PLMN

 

 

♦Example

AT+CSPN=? OK AT+CSPN?

+CSPN: “CMCC”,0

 

OK

 

 

 

 

AT+CSQ      Query Signal Quality

This command is used to return received signal strength indication <rssi> and channel bit error rate <ber> from the ME.

Test command returns values supported by the TA as compound values.

 

T) AT+CSQ=?

Response

+CSQ: (list of supported <rssi>s),(list of supported <ber>s)

OK

E) AT+CSQ

Response

+CSQ: <rssi>,<ber>

OK

or

ERROR

 

 

♦Parameter
Description
<rssi>

0                    -113dBm or Less

1                   -111dBm

2…30            -109… -53dBm

31                 -51dBm or Greater

99                  not known or not detectable

100                -116dBm or Less

101                -115dBm

102…192       -114…-26dBm

199                not known or not detectable

100…199       expand to TDSCDMA, indicate RSCP received?

<ber>

(in percent)

0        <0.01%

1        0.01% ~ 0.1%

2        0.1%~0.5%

3        1.0% ~ 2.0%

4        1.0% ~ 2.0%

5        2.0% ~ 4.0%

6        4.0% ~ 8.0%

7        >=8.0%

99        not known or not detectable

AT

 

♦Example

AT+CSQ

+CSQ: 22,0

 OK

 

 

  

AT+AUTOCSQ      Set CSQ Report

This command is used to enable or disable automatic report CSQ information,

when automatic report enabled, the module reports CSQ information every five seconds

or only after <rssi>or<ber> is changed, the format of automatic report is “+CSQ: <rssi>,<ber>”.

 

T) AT+AUTOCSQ=?

Response

+AUTOCSQ: (list of supported<auto>s),(list of supported<mod e>s)
OK

R) AT+AUTOCSQ?

Response

+AUTOCSQ: <auto>,<mode>
OK

W) AT+AUTOCSQ=<auto>[,<mode>]

Response

OK

or

ERROR

 

 

♦Parameter
Description
<auto>

0    disable automatic report

1    enable automatic report

<mode>

0   CSQ automatic report every five seconds

1   CSQ automatic report only after <rssi>or<ber>is changed

NOTE:

If the parameter of <mode> is omitted when executing write command, <mode> will be set to default value.

 

 

♦Example

AT+AUTOCSQ=?

+AUTOCSQ: (0-1),(0-1)

 

OK AT+AUTOCSQ?

 

 

 

AT+CSQDELTA     Set RSSI delta change threshold

This command is used to set RSSI delta threshold for signal strength reporting.

T) AT+CSQDELTA=?

Response

+CSQDELTA: (list of supported <delta>s)
OK

R) AT+CSQDELTA?

Response

+CSQDELTA: <delta>
OK

or

ERROR

W) AT+CSQDELTA=<delta>

Response

OK

or

ERROR

E) AT+CSQDELTA

Response

Set default value<delta>=5:OK

 

 

♦Parameter
Description
<delta> Range: from 0 to 5.

 

 

♦Example

AT+CSQDELTA?

+CSQDELTA: 5

 OK

 

 

 

AT+CATR      Configure URC destination interface

This command is used to configure the serial port which will be used to output URCs.

We recommend configure a destination port for receiving URC in the system initialization phase,

in particular, in the case that transmi large amounts of data, e.g. use TCP/UDP and MT SMS related AT command.

 

T) AT+CATR=?

Response

+CATR: (list of supported <port>s)
OK

R) AT+CATR?

Response

+CATR: <port>
OK

W) AT+CATR=<port>

Response

OK

or

ERROR

 

 

♦Parameter
Description
    <port>

0       –    all ports

1       –    use UART port to output URCs

2       –    use MODEM port to output URCs

3       –    use ATCOM port to output URCs

4       –    use cmux virtual port1 to output URCs

5       –    use cmux virtual port2 to output URCs

6       –    use cmux virtual port3 to output URCs

7       –    use cmux virtual port4 to output URCs

 

 

♦Example AT+CATR=1 OK AT+CATR?
+CATR: 1OK

 

 

 

AT+CPOF       Power Down The Module

This command is used to power off the module.

Once the AT+CPOF command is executed, The module will store user data and deactivate from network, and then shutdown.

 

T) AT+CPOF=?

Response

OK

E) AT+CPOF

Response

OK

 

 

♦Example

AT+CPOF

OK

 

 

 

 AT+CRESET       Reset The Module

This command is used to reset the module.

 

T) AT+CRESET=?

Response

OK

E) AT+CRESET

Response

OK

 

 

♦Example

AT+CRESET=?

OK

AT+CRESET

OK

 

 

 

AT+CACM       Accumulated Call Meter

This command is used to reset the Advice of Charge related accumulated call meter value in SIM file EFACM.

 

T) AT+CACM=?

Response

OK

or

ERROR

R) AT+CACM?

Response

+CACM: <acm>

OK

or

ERROR

or

+CME ERROR: <err>

W) AT+CACM=<passwd>

Response

OK

or

ERROR

or

+CME ERROR: <err>

E) AT+CACM

Response

OK

or

ERROR

or

+CME ERROR: <err>

 

 

♦Parameter
Description
<passwd> String type, SIM PIN2.
<acm> String type, accumulated call meter value similarly coded as <ccm>under +CAOC.

 

  

♦Example

AT+CACM?

+CACM: “000000”

 OK

 

 

  

AT+CAMM       Accumulated Call meter Maximum

This command is used to set the Advice of Charge related accumulated call meter maximum value in SIM file EFACMmax.

 

T) AT+CAMM=?

Response

OK

or

ERROR

R) AT+CAMM?

Response

+CAMM: <acmmax>

OK

or

ERROR

or

+CME ERROR: <err>

W) AT+CAMM=<acmmax>[,<passwd>]

Response

OK

or

ERROR

or

+CME ERROR: <err>

E) AT+CAMM

Response

OK

or

ERROR

or

+CME ERROR: <err>

 

 

♦Parameter
Description
<acmmax>

String type, accumulated call meter maximum value similarly codedas <ccm> under AT+CAOC,

value zero disables ACMmax feature.

<passwd> String type, SIM PIN2.

 

 

♦Example

AT+CAMM?

+CAMM: “000000”

 OK

 

 

 

 

AT+CPUC       Price Per Unit and Currency Table

This command is used to set the parameters of Advice of Charge related price per unit and currency table in SIM file EFPUCT..

 

T) AT+CPUC=?

Response

OK

or

ERROR

R) AT+CPUC?

Response

+CPUC: [<currency>,<ppu>]

OK

or

ERROR

or

+CME ERROR: <err>

W)

AT+CPUC=<currency>,<ppu>[,<passwd>]

Response

OK

or

ERROR

or

+CME ERROR: <err>

 

 

♦Parameter
Description
<currency>

String type, three-character currency code (e.g. “GBP”, “DEM”),

character set as specified by command Select TE Character Set AT+CSCS.

<ppu> String type, price per unit, dot is used as a decimal separator. (e.g.”2.66″).
<passwd> String type, SIM PIN2.

 

  

♦Example

AT+CPUC?

+CPUC: “GBP” , “2.66”

 OK

 

 

 

AT+CAMM        Real Time Clock Management

his command is used to manage Real Time Clock of the module.

 

T) AT+CCLK=?

Response

OK

R) AT+CCLK?

Response

+CCLK: <time>
OK

W) AT+CCLK=<time>

Response

OK

or

ERROR

 

 

♦Parameter
Description
<time>

String type value; format is “yy/MM/dd,hh:mm:ss±zz”,

where characters indicate year (two last digits), month, day, hour, minutes, seconds

and time zone (indicates the difference, expressed in quarters of an hour, between the local time and GMT;

three last digits are mandatory, range -47…+48).

E.g. 6thof May 2008, 14:28:10 GMT+8 equals to “08/05/06,14:28:10+32”.

 

NOTE:

1.Time zone is nonvolatile, and the factory value is invalid time zone.

2.Command +CCLK? will return time zone when time zone is valid, and if time zone is 00,

command +CCLK? will return “+00”, but not “-00”.

 

 

♦Example

AT+CCLK=“08/11/28,12:30:33+32”

OK

AT+CCLK?

+CCLK: “08/11/28,12:30:35+32”

 

 

 

AT+CMEE     Report Mobile Equipment Error

This command is used to disable or enable the use of result code “+CME ERROR: <err>”

or “+CMS ERROR: <err>” as an indication of an error relating to the functionality of ME;

when enabled, the format of <err> can be set to numeric or verbose string.

 

T) AT+CMEE=?

Response

+CMEE: (list of supported <n>s)
OK

R) AT+CMEE?

Response

+CMEE: <n>
OK

W) AT+CMEE=<n>

Response

OK

or

ERROR

E) AT+CMEE

Response

Set default value:

OK

 

 

♦Parameter
Description
<n>

0       –Disable result code,i.e. only “ERROR” will be displayed.

1       –Enable error result code with numeric values.

2       –Enable error result code with string values.

 

 

♦Example

AT+CMEE?

+CMEE: 2

 OK

AT+CPIN=”1234″,”1234″

+CME ERROR: incorrect password

AT+CMEE=0

 OK

AT+CPIN=”1234″,”1234″ ERROR

AT+CMEE=1 OK

AT+CPIN=”1234″,”1234″

+CME ERROR: 16

 

 

 

 

AT+CPAS       Phone Activity Status

This command is used to return the activity status <pas> of the ME. It can be used to interrogate the ME before requesting action from the phone.

NOTE: This command is same as AT+CLCC, but AT+CLCC is more commonly used. So AT+CLCC is recommended to use.

 

T) AT+CPAS=?

Response

+CPAS: (list of supported <pas>s)
OK

E) AT+CPAS

Response

+CPAS: <pas>
OK

 

 

♦Parameter
Description
<pas>

0    –    ready (ME allows commands from TA/TE)

3       –    ringing (ME is ready for commands from TA/TE, but the ringer is active)

4       –    call in progress (ME is ready for commands from TA/TE, buta call is in progress)

 

 

♦Example

RING (with incoming call) AT+CPAS

+CPAS: 3

 OK

AT+CPAS=?

+CPAS: (0,3,4)

 OK

 

 

 

AT+SIMEI    Set IMEI For The Module

This command is used to set the module’s IMEI value.

 

T) AT+SIMEI=?

Response

OK

R) AT+SIMEI?

Response

+SIMEI: <imei>
OK

or

ERROR

W) AT+SIMEI=<imei>

Response

OK

or

ERROR

 

 

♦Parameter
Description
<imei> The 15-digit IMEI value.

 

 

♦Example

AT+SIMEI=357396012183170

OK

AT+SIMEI?

+SIMEI:357396012183170

 OK

AT+SIMEI=?

OK

 

 

 

AT+SMEID        Request Mobile Equipment Identifier

Only task effect in 7600CE

 

R) AT+SMEID?

Responses

+SMEID: <MEID>

OK

or

ERROR

 

 

♦Parameter
Description
<MEID> Mobile Equipment Identifier (string, without double quotes).

 

 

♦Example

AT+SMEID?

+SMEID: A1000021A5906F

 

  

 

 AT+CSVM        Voice Mail Subscriber Number

Execution command returns the voice mail number related to the subscriber.

 

T) AT+CSVM=?

Response

+CSVM: (0-1), “(0-9,+)”, (128-255)

OK

or

ERROR

R) AT+CSVM?

Response

+CSVM: <valid>, “<number>”,<type>

OK

or

ERROR

W) AT+CSVM=<valid>,“<number>”,<type>

Response

OK

or

ERROR

 

 

♦Parameter
Description
 <valid>

Whether voice mail number is valid:

0       –    Voice mail number is invalid.

1       –    Voice mail number is valid.

<number> String type phone number of format specified by <type>.
<type> Type of address octet in integer format. see also AT+CPBR <type>

 

 

♦Example

AT+CSVM?

+CSVM: 1 ,”13697252277″,129

 OK

 

 

 

 

 

Indication of Voice Mail 

This module supports voice mail function; the subscriber number is configured by AT+CSVM command,

the following table shows the URC related Voice Mail.

 

Box Empty

+VOICEMAIL: EMPTY

This indication means the voice mail box is empty

New Message

+VOICEMAIL: NEW MSG

This indication means there is a new voice mail message notification received. This is for CPHS.

Voice Mail Status Updated

+VOICEMAIL:  WAITING,<count>

This indication means that there are <count> number of    voice mail messages that needs to be got.

 

 

♦Parameter
Description
<count> Count of voice mail message that waits to be got.

 

 

♦Example

+VOICEMAIL: WAITING, <count>

+VOICEMAIL: WAITING, 5

 

 

 

 

CME ERROR codes

This result code is similar to the regular ERROR result code.

The format of <err> can be ethier numeric or verbose string, by setting AT+CMEE command.

<err> of numeric format <err> of verbose format
0 Phone failure
1 no connection to phone
2 phone adaptor link reserved
3 operation not allowed
4 operation not supported
5 PH-SIM PIN required
6 PH-FSIM PIN required
7 PH-FSIM PUK required
10 SIM not inserted
11 SIM PIN required
12 SIM PUK required
13 SIM failure
14 SIM busy
15 SIM wrong
16 incorrect password
17 SIM PIN2 required
18 SIM PUK2 required
20 memory full
21 invalid index
22 not found
23 memory failure
24 text string too long
25 invalid characters in text string
26 dial string too long
27 invalid characters in dial string
30 no network service
31 network timeout
32 network not allowed – emergency calls only
40 network personalization PIN required
41 network personalization PUK required
42 network subset personalization PIN required
43 network subset personalization PUK required
44 service provider personalization PIN required
45 service provider personalization PUK required
46 corporate personalization PIN required
47 corporate personalization PUK required
100 Unknown
103 Illegal message
106 Illegal ME
107 GPRS services not allowed
111 PLMN not allowed
112 Location area not allowed
113 Roaming not allowed in this location area
132 service option not supported
133 requested service option not subscribed
134 service option temporarily out of order
148 unspecified GPRS error
149 PDP authentication failure
150 invalid mobile class
257 network rejected request
258 retry operation
259 invalid deflected to number
260 deflected to own number
261 unknown subscriber
262 service not available
263 unknown class specified
264 unknown network message
273 minimum TFTS per PDP address violated
274 TFT precedence index not unique
275 invaild parameter combination

 

 

 

CME ERROR codes of FTP

 

<err> of numeric format <err> of verbose format
201 Unknown error for FTP
202 FTP task is busy
203 Failed to resolve server address
204 FTP timeout
205 Failed to read file
206 Failed to write file
207 It’s not allowed in current state
208 Failed to login
209 Failed to logout
210 Failed to transfer data
211 FTP command rejected by server
212 Memory error
213 Invalid parameter
214 Network error

Adsense

EMW3070

Viewed Page List