페이지 선택
Generic selectors
Exact matches only
Search in title
Search in content
Search in pages
AT Commands For HSIC_LAN

  

Command Description
AT+CENABLELAN Enable LAN function
AT+CLANMODE Set LAN mode
AT+CLANCTRL Set LAN configure
AT+CHSICSLEEP Allow Hsic Device Go to AutoSleep

 

 

 

 

AT+CENABLELAN     Enable LAN Function

 

W) AT+CENABLELAN=<onoff>

OK

or

ERROR

 

 

<onoff>

0     Close the LAN9730

1     Open the LAN9730

 

 

Example

AT+CENABLELAN=1

OK

 
 

NOTE

LAN9730 is not opened in default, if want to open the LAN9730, you can run AT+CENABLELAN=1.

After run this command, the module will restart automatically, then the LAN9730 will be opened.

If want to close the LAN9730, you can run AT+CENABLELAN=0.

After run this command, the module will restart automatically, then the LAN9730 will be closed.

WIFI firmware doesn’t care this AT command.

 

 

 

 

AT+CLANMODE     Set LAN Mode

 

T) AT+CLANMODE=?

+CLANMODE: (list of supported <mode>s)

OK

R) AT+CLANMODE?

+CLANMODE: <mode>

OK

W) AT+CLANMODE=<mode>

OK

or

OK

 

 

<mode>

0     lan mode

1     wan mode

2     static ip mode

 

 

 

Example

AT+CLANMODE?

+CLANMODE: (0,1)

OK

 

AT+CLANMODE=1

OK    

                                               

                                                           

NOTE

Module works in lan mode in default.

If want to use another mode, need to run at+clanmode=<mode>, after run this command, module will restart automatically, then the module will work in target

mode.

 

 

 

 

AT+CLANCTRL     Set LAN Configure

 

T) AT+CLANCTRL=?

+CLANCTRL: (list of supported <option>s)

 

OK

W) AT+CLANCTRL=<option>,[[type/ip],[netmask]]

OK

or

ERROR

 

 

<option>

0        uninstall driver

1        install driver

2        set mac address

3        set ip address

4        bring up eth0

5        bring down eth0

<type>

1        bcm898xx

2        at803x

<ip> LAN ip address (Range: 192.168.*.*).
<netmask >

Range     255.255.*.*

if the parameter is not set, will use the default value:255.255.255.0

 

 

Example

AT+CLANCTRL=3,”192.168.1.1”                                       

Set ip.

The netmask is use default value 255.255.255.0                                                                                    

OK

 

AT+CLCANCTRL=3,”192.168.1.1”,”255.255.2 55.0”

Set ip and netmask.

The netmask is 255.255.255.0

OK

 

 

NOTE

Uninstall driver (option=0). Not support for HSIC LAN, Only Support SGMII LAN. Please don’t run this command on HSIC LAN module

Install driver (option=1). Not support for HSIC LAN, Only Support SGMII LAN.

Set mac address (option=2). Support for HSIC LAN, But the module will auto set the Mac address. So there is no need to run the command.

Set ip address (option=3). When module work in static ip mode. Use this command set ip and netmask.

Bring up eth0 bring up eth0 (option=4). equal to “ifconfig eth0 up”

Bring down eth0 (option=5). equal to “ifconfig eth0 down”

 

 

 

 

AT+CHSICSLEEP     Allow HSIC Device Go To AutoSleep

 

T) AT+CHSICSLEEP=?

+CHSICSLEEP: (list of supported <state>s)

 

OK

R) AT+CHSICSLEEP?

+CHSICSLEEP: <state>

 

OK

W) AT+CHSICSLEEP=<state>

OK

or

ERROR

 

 

<state>

0       Don’t allow the hsic device go to autosleep

1       Allow the hsic device go to autosleep

 

 

Example

AT+CHSICSLEEP =1

OK

 

AT+CHSICSLEEP?

+CHSICSLEEP: 1

OK

 

 

NOTE

If the module needs to go to sleep, user needs to execute following steps:

1. AT+CHSICSLEEP=1

2. AT+CLANCTRL=5

 

 

 

 

 

Adsense

EMW3070

Viewed Page List